雙組份打膠機采用無觸點電器控制系統控制，換向靈敏可靠，其獨特的方便可調試配比機構，大限度地保證雙組份膠近乎苛刻的配比要求，出膠連續均勻，涂膠效果好，生產效率高。今天小編給大家總結一下雙組份打膠機的注意事項，希望對大家有所幫助！
The two-component glue beater is controlled by contactless electrical control system, which is sensitive and reliable in reversing direction. Its unique convenient and adjustable proportioning mechanism ensures that the two-component glue meets the strict proportioning requirements to a great extent. The glue is produced continuously and evenly, the glue effect is good, and the production efficiency is high. Today, Xiaobian summarizes the matters needing attention of the two-component glue punch, hoping to be helpful to you all! 
1.由于雙組份密封膠的固化需要一定時間，因此雙組份打膠機，已涂了雙組份密封膠的玻璃應水平輕輕搬動。A組、B組份膠應保持清潔，嚴防異物進入膠中。
1. Since the curing of two-component sealant takes some time, the glass coated with two-component sealant should be moved horizontally and gently. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
2.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每?jī)山M清洗一次
2. The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and check valve with clear B component are recommended to be cleaned once for each two groups.
3.如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。
3. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.

4.當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
4. When the rubber gun is not used for a long time (more than a week), the gun body should be removed and the residual colloid in the rubber gun and mixer should be cleaned with solvent.
5.混膠器應經常保持暢通，以保證良好的出膠效果。
5. Mixers should be kept unblocked regularly to ensure good gumming effect.
6.高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
6. High-pressure hose shall not be forced to extrude or bend to prevent the normal operation of the system.
7.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直至單一的A組份膠從槍口排出為止。
7. In the continuous working process, the rubber gun should not stop working for more than 20 minutes at a time. Otherwise, the whole mixture should be produced by using component A glue until a single component A glue is discharged from the muzzle of the gun.
今天給大家介紹的精彩內容到這里就結束了，小編在這里十分感謝大家的閱讀，如果大家想要了解更多的相關咨詢，可以把我們的網址：http://linshi.jncsjx.com添加到收藏，或者搜索關鍵詞：雙組份打膠機，也可以找到我們。
Today's wonderful content for you is over. The edition here is very grateful for your reading. If you want to know more about the relevant consultation, you can add our website: http://linshi.jncsjx.com to the collection, or search keywords: two-component glue machine, you can also find us.