中空玻璃設備的保養總體方法不難，關鍵是要做好對設備滑輪的保養潤滑，保證工作時候的電壓穩定，預防電機出現燒毀的情況，確保設備能夠正常運行就可以了。

　　The overall maintenance method of the insulating glass equipment is not difficult. The key is to do well the maintenance lubrication of the equipment pulley, ensure the voltage stability at work time, prevent the motor from burning down, and ensure that the device can run normally.

　　萬一設備在工作期間發生了重大的故障，那么就需要聘請的維修人員前來處理。非人員切莫擅自拆機維修。此外需要注意的一點是，當故障發生需要檢修的時候，必須要先把總電源給切斷了。

　　In case of a major failure during the operation of the equipment, the professional maintenance personnel need to be hired to deal with it. Non professionals do not disassemble or repair. In addition, one point to be noted is that when the failure needs to be overhauled, the total power supply must be cut off first.

　　要使得中空玻璃設備使用效果理想，玻璃清洗徹底干凈，大程度的延長其使用壽命，就必須要注意其基本的保養常識。在設備使用過程中注意對其進行正確的保養。

　　We must pay attention to basic maintenance knowledge to make the insulating glass equipment ideal and clean and maximize the service life. Pay attention to the correct maintenance of the equipment during the use of the equipment.

　　其一，對傳送輥的維護。中空玻璃設備的關鍵零件傳送輥必須要注意定期進行潤滑處理，在設備運轉之前要先檢查器潤滑情況，看油位線標是否正常，油位必須要保持在滑標的中心線以上才可以。

　　First, the maintenance of the transmission roll. The key parts of insulating glass equipment must be careful to lubricate regularly. Before the operation of the equipment, check the lubricants first, see whether the oil level mark is normal, and the oil level must be kept above the centerline of the slide mark.

　　其二，設備系統的水路維護。設備內的水箱要保證系統水循環的正常，每周要對水箱進行一次徹底的清洗，要對噴水嘴進行常規性的檢查，一旦發現有堵塞就要馬上進行疏通清理。此外還有風路的維護，設備風機的運行情況要保持良好穩定。

　　Secondly, the maintenance of the water route of the equipment system. The water tank in the equipment should ensure the normal water circulation of the system. Once a week, the tank must be thoroughly cleaned. The nozzle should be checked routinely. Once there is a blockage, it is necessary to dredge and clean up immediately. In addition to the maintenance of the wind road, the operation of the equipment fan should be kept good and stable.

　　本文由雙組份打膠機為您提供，我們的網站是:http://linshi.jncsjx.com我們將以全心全意的熱情為您提供更優質的服務，歡迎您的訪問!

　　This article is provided by two component glue machine. Our website is: http://linshi.jncsjx.com, we will provide you with better service with wholehearted enthusiasm, welcome your visit.