1. The two-component sealant applicator equipment should be installed in a dry, dust-free and non-corrosive environment (this requirement is the same as other equipment, of course, if the conditions are not met, at least strive for non-corrosive gas, after all, there are wires and pipelines in the equipment, which are not highly resistant to corrosion).

2、室內溫度控制在10～40度的室內堅硬地面上，地面應水平度要好。（小編這里說的地面水平度要好不一定要非常的平整才行，我們的設備在設計之初已經考慮到了地面復雜性的因素所以對地面平整度是有相當大的忍讓度的，只要不是幅度提別的大一般都可以正常工作。）

2. The indoor temperature shall be controlled on the indoor hard ground of 10~40 degrees, and the ground shall be level. (The ground levelness mentioned by the editor here needs to be very smooth. Our equipment has taken into account the complexity of the ground at the beginning of design, so it has a great tolerance for the ground levelness. It can normally work as long as it is not significantly improved.)

3、雙組份打膠機安裝之前，應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況，之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備無法正常運行，我們的工作人員到現場后才排查出的原因。

3. Before installing the two-component sealant applicator, it is necessary to check whether there is deformation, damage and loosening of fasteners caused by transportation and moving. Previously, a customer knocked off a part of the intelligent control system of the equipment in the process of moving the sealant applicator, which caused the equipment to fail to operate normally. Our staff only found out the reason after arriving at the site.

4、我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地，把氣源接入機器所配帶的氣源接口，確保無漏氣現象。

4. First, we can adjust the levelness of the equipment by adjusting the lifting anchor bolts of the equipment according to the actual situation of the ground levelness until the equipment is horizontal and stable. Then connect the wires according to the drawing and reliably connect the air source to the air source interface of the machine to ensure that there is no air leakage.

5、向油槽中加注液壓油至指定位置，46#液壓油（約為50升左右）。

5. Fill the oil tank with hydraulic oil to the specified position, 46 # hydraulic oil (about 50 liters).

6、接通電源并打開查看設備是否能夠正常運行。

6. Turn on the power and turn it on to check whether the device can operate normally.

本文由雙組份打膠機提供技術支持，更多的詳細精彩內容請點擊我們的網站 http://intelyalan.cn我們將會全心全意為您提供滿意的服務。

This article is supported by the two-component gluing machine. For more details, please click our website http://intelyalan.cn We will wholeheartedly provide you with satisfactory service.